It's so clean and it does what they say it does. I have to say a bad thing or nobody will believe how good these hydrants are: I struggled to clip in a new fitting when the system was under pressure, so I'll shut off pressure if I need to change out fittings to avoid damaging them. That's like a twice a year thing for me. The 3/4" PEX-A attachment is the bomb (photo). After swapping out my old 1/2" copper with 3/4" PEX-A and installing this hydrant my outside GPMs went from 7.5 to 12. Compliment sandwich complete!

Installation was easy. Product seems good so far. Just make sure you have a valve on the hose connector or you will get soaked when connecting.

I bought 2 hot+cold hydrants and 2 V2+hydrants from Aquor, and 3 out of 4 of those worked perfectly but one of the V2's would drip constantly after disconnecting the hose connector. Customer service responded quickly and walked me through some troubleshooting steps to try and dislodge potential debris that might not be allowing the operating rod to close all the way, and after that didn't work, quickly shipped me a warranty unit at no cost. We were under construction, and getting a replacement unit immediately was important, and it arrived within days. Once we removed the "defective" unit, we see that it isn't defective at all but the plumber didn't follow the instructions, and used teflon tape which gummed up the mechanism!

5 stars for Aquor, 10 stars even
1 star for the plumber my GC hired

And my (very constructive) feedback: Aquor should put a large label on the hydrant itself, in both English and (more importantly) in Spanish, stuck to the hydrant in a way that hopefully forces someone to remove and read it before install, reminding them to not use teflon tape and that the o-ring built into the hydrant is sufficient to stop leaks, because nobody will read the manual. And I guess, never trust your contractor and watch everything they do, or... just do it yourself!

These hydrants are extremely well made. Love the fact there is no packing or turning handle that will leak over time. I’ve installed all four myself so not beyond the skills of a decent do-it-yourself homeowner.

I got my first Aquor faucet when I got tired of replacing “frost-free” hose bibs almost every year. After installing the first Aquor I was actually looking forward to the other two hose bibs failing. Fast forward two years and I just replaced my last hose bib with an Aquor. I’ll never use anything else, they’re so easy to use and so reliable. I’ll never again have the dread of cracking open a hose bib for the first time in the spring and watching the vacuum breaker leak water everywhere. Install pictures show the custom mounting block I made out of PVC trim.

So I don't know if you're looking at this product because of the solution of looking clean or because of how well it works. But regardless if there's any products out there that you can consider competition consider this brand because of their customer service. I own four and head an issue with a product that I believe my installer damaged and they covered it. Great customer service will recommend and buy in the future

Purchased the V2 for our new construction home. We we, nor our plumber, were familiar with Aquor, but I knew I wanted them! I chose the Gray polymer which is the least expensive option, and I was afraid it would look cheap. It doesn’t look cheap at all! I might upgrade to a more polished cover later, but this will work with our brick for now! Our plumber wasn’t intimidated with the install and commented on how neat it was! I can’t wait to start using them!

High quality, easy to install, and looks great.

Very nice well made fitting I had to build a box to mount it as I ordered 12"and should have gone for 10"
Arrived on time happy with purchase.

Good product overall. Best looking hose bib ever.

I had these installed for a new build. They are sleek and looks so much nicer than traditional hose faucets.

Great products, have used them on several homes that I have built in my clients seem to love them

Loving this product. Works great and high quality.

Pretty slick new products on both the metal finished debris covers (we did some black and white) and also the no show mounting boxes. Being in new construction the exterior trades have a tendency to remove covers and not reset properly so the no show boxes keep a clean look but also makes it a permanent install

Had to install a spigot in a wall, there was nothing I could find that would work. Finally found Aquor and it works great. Easy to install and prevents freezing I the winter. Looks great too.

I like the quality of the construction of Aquor. I haven’t installed my Aquor. I’m waiting for the spring. I’m thrilled to use it.

This is a great idea, and very stylish as well. I needed something to replace my old outdoor water faucet as I was remodeling my house and installing steel board & batten siding. The existing location was pretty low coming through the sill plate. The V2 was a perfect fit and easy to install, giving us a better access to the hydrant. Quality made with stainless steel.

The product is great, well made, and easy to install. I had a small issue with one of them and customer service was quick to resolve the issue without any trouble. I would definitely buy these in the future.

I had a slight planning error and had to move the spigot I had aleast purchased to another location which required a different size stem. Contacted customer service and within a few minutes had the correct one on the way. Super impressed with the way things were handled. As far as the product, I absolutely love the look of the flush cover. So far everything looks and works great. Time will tell how it holds up but so far so good.

Love my new faucets! Have an old house that had old drippy nasty faucets, all replaced now with the V2+.

The Aquor House Hydrant V2+ is a heavy gauge, stainless, with perfectly fitting and working o-rings. Gentle twisting of the inside connector tube just to the stop and you’re ready to connect to your piping. The connection to your plumbing could be as simple as threading on, or you may have to add a fitting to your piping. A word to the wise; purchase stainless teflon tape not the regular white or blue. It’s best not to use galvanized fittings if you have a copper line. And you may want to add a 1/4 turn stop valve, to prevent water from spraying when you twist the hose connector in. You’ll get the hang of twisting on the outside hose connector. It only took me twice.

I recommended this to family members already. Currently Aquor is offering 10% off next purchase and a free hose connector for an honest review. Register right away and I recommend purchasing the Aquor Wide Grip Hose Connector just in case the one that accompanies the hydrant (Aquor V2+) ever were to break. I don’t think it will, as it is also stout, but I won’t take the chance.

We are new construction and we had no problem installing. It looks beautiful and works great. The material is good quality. Would definitely recommend!

Good spigot upgrade

Love the look and quality of these hydrants! My plumber recommended this product when I needed to replace my existing hydrant. I am very impressed with the appearance on my recently built patio. Works great!

I have remodeled three bathrooms using copper and PEX piping. On the cast aluminum connector on the V2 Hydrant I wrapped the threads with Teflon tape. After installing in the brick wall, I had a very tiny leak at the threaded connection. I called tech support and was told to use Teflon Tape and plumbers thread sealant (Like the instructions say to). After removing the hydrant I use new Teflon tape and thread sealant and of course, No Leaks. I have never used bothTeflon and sealant together, but it worked. Live and Learn.